Friday, 13 December 2019

STELLA IS BACK

It's done and I want it out of the way, was the message. I was planning to get Richard and his car transporter to collect Stella on Friday 13th. However Trevor wanted it gone before it got that perfect paint job damaged and covered in dust in his crowded workshop.

It was all going to be a rush as it was only 1.30 pm when Trevor called and he had a transporter arranged for 3pm and would I arrive in time to lead the transporter and Stella back home.




I arrived just in time and snapped a few shots of Stella just before she was loaded up for the trip home, shiny? Not arf!!!

Thursday, 5 December 2019

PRIMED AND READY TO GO

Trevor called and said the Stag has been rubbed right back to bare metal, etched primed and the fist couple of coats of grey primer have been applied and rubbing back has started and would I like to come and have a look. I was up there straight away.




I have never seen Stella looking so smooth, admittedly a bit blotchy, but looking good. Trevor asked me check on the paint code, which is 19 Triumph White as he was about to order the paint,

I assumed is would be water based, but no, Trevor assured me it was going to be a top quality two pack and would likely be finished and ready for collection by the end of the week, we shall see!

Tuesday, 19 November 2019

HEADLIGHTS

When I stripped the four headlights from the car including the black bowls or buckets that the glass part sits in, I realised how scruffy all the bits looked.

The four chromed bezels were very grubby on the outside and on the inside there was loads of rust, so I started with those. My polishing wheel brought the chrome back to more than acceptable, I then sanded down the inside to get rid of the rust, carefully masked off the shiny chrome and applied three coats of silver Hammerite. Photos below show job done.


Next were the four inner bezels that the glass units sit in and allow for adjustment of aim. This time I used a wire brush in my electric drill, clamped into my workmate and scrubbed all the rust away. Again three sprayed coats of silver Hammerite were applied.The photo shows before and after. The after is on the left, just in case there was any doubt.


Now it was time for the bowls or buckets, the outside of each of the bowls was covered in oily cack which white spirit and paper cloth removed, but it was both sides of the rims that were rusty and again the wire brush cleaned it up and the cables were masked. Three coats of smooth black Hammerite and now all four were nice and shiny inside and out. I forgot to take pictures at this point as I was excited to get them all reassembled.



 However I decided to upgrade the halogen bulbs to LED's, so ordered four H1 units, I also decided to buy new glass headlamp bowls to maximise efficiency of the LED's. I quickly realised the H1 LED's would not fit in the dip glass bowl, these bowls are now all designed to take the main/dip type H4.bulbs, I had a chat with Gil from BetterCarLighting and he suggested I upgrade to having four H4 LED's and rewire through relays to give me 4 dip beams and 4 main beams. Not only will each LED give far more light than the old halogen bulbs, but I will be doubling from 2 dip and 2 main headlights, the improvement of light should be amazing. Gil also said that for town driving, four dipped beams might be too bright and suggested that a small switch be mounted on or under the dash, that would allow the two inner dipped lamps to be turned off. I agreed with this suggestion and Gil included with the H4 bulbs a switch and wiring harness, plus a wiring diagram.


The photo above shows one of the new glass bowls fitted with my first choice of a H1 LED. The final choice of H4 LED's came with their own wiring harness, meaning that the wires in the black metal buckets that I had so carefully masked off before spraying, I now had to cut off and replace with the new wiring.


And there we are; a view of a freshly sprayed bucket and the complete assembly, polished rims, new glass bowl fitted with a H4 LED already to be installed in Stella when she returns.




Monday, 11 November 2019

NEW METAL

I was expecting a call from Trevor at the bodyshop and he didn't disappoint, he said the welding was done, but he needed to discuss the way forward in respect of the amount of paint that they had had to remove to get to bare metal.

I was there the next day and sure enough all the wheel arches and both sills had neatly stitched in new metal. I was surprised that they had probably only used about 20% of each of the repair panels. At the rear it was only the arches that had been replaced and the major part of each panel was propped up against the wall.



 The front arches had taken slightly more metal, but the rest of the wings were in very good order. Only the very bottom of the sills had been replaced and there was no trace of rust internally as somebody in the past had sprayed all of the cavities with Waxoil. There were several other welded repairs, a small area at the bottom of the drivers door and left front valance..


Trevor showed me how thick the paint was where they had feathered it back to bare metal for the repairs, he pointed out, that there could be a future problem of the new paint crazing particularly in this transition area and it would be much better to cut all the old paint back to the metal. They had already had to do this on the bonnet, which was now in primer.


You have to rely on the expert for good advice and I had it on good authority that Trevor was an honest professional, so I agreed, but it seems that I should still get Stella back before Christmas.








Thursday, 7 November 2019

T BAR

I couldn't leave the T bar in its original condition, there was a little white over spray at each end of the T from some previous owners respray, a small split on the top and generally it looked rather tired. I did at first think I would only order the black vinyl cover as the foam underneath felt firm enough, but as soon as I unzipped and started to peel back the old cover I was mighty pleased I had ordered the five piece foam set as well as the cover.


Bits of sticky, crumbly, grubby foam ended up going all over the dining table, I should say that I had taken the precaution of covering the table first. I then decided to finish off removing the bulk of the  foam outside and I carefully carried it out and put it onto the garden table.

In the garage I scrapped away the residue and cleaned it up with white spirit and paper cloth, before I brought it back onto the lounge table to glue on the foam sections. I got carried away with the spray impact adhesive and forgot to take any photos until I had got the cover onto the T part.


This went easier than I expected, but I did wrap the foam, on the non zip side with cling film and this allowed the very snug sleeve to be pulled up that side of the T, that's the side that I have already glued the end. However when I started to zip the cover over the I part of the T, the cover was a little slack and wrinkly and I realised I was going to have to find some extra foam to stuff down one side to fill the cover.


I searched EBay for tubular foam and came up with foam designed for cushioning toes, bunions, corns etc. It came in various internal diameter, I chose the biggest at 25mm and 4 lengths of 25cm. I used two and a half lengths, the photo shows just one length temporally tucked in. I zipped the cover up the making sure the additional foam didn't move and now no wrinkles.


Just had to pull the cover tight over the small end and trim off the excess material and stick it down, this was fiddly work, snipping away to ensure there was minimum overlap as I pulled the material into the corners, patience pays off though, but it was several hours and my thumbs were a bit sore.




I'm pretty chuffed, that will be the first thing back on the car when I get it back, which seems as if it will be before Christmas, but that's another story.


Thursday, 31 October 2019

THE BODY

After two weeks at the bodyshop, I called Trevor and he was anxious for me to visit, Trevor had lost my phone number and was very pleased I had called. I popped in the next day and there she was, up on blocks, doors off, wheels off, paint and filler stripped back, with all the tin worm exposed. There had been, as was expected, a lot of filler masking the rot and some evidence of previous welding, but fortunately the rust was not extensive and was confined to just the outer skin.


It was decided that all four quarters needed repair panels and also the sills, unfortunately the photos don't really show the problem, but as I said not to bad considering the age of the car. I ordered the panels as soon as I got home and it was all with me before lunch time the next day.



I delivered everything the next day, including a new windscreen rubber seal, as the widow will have to come out. I was very pleased with progress and I saw Trevor make a note of my mobile number with a promise to call when it was time for me to re-visit, I expect that will be after all the welding is done.


Monday, 14 October 2019

THE TEASE IS OVER

Completing the stripping of Stella went easier than I expected. I tackled the doors next, I knew that removing the door cards and handles would be OK as I had done that before, but taking out the trim, glass and chrome frame plus the electric winder was a new challenge. The instructions in the manual are a bit sketchy, but a bit of common sense and it all came away.



Next was the front end. I had been wondering how I was going to get access to the bumper side bolts, but once I had removed the headlamps and shells it was obvious, again everything either unscrewed or unbolted without a problem. The black goo that was holding the chrome trim was cut through and all the trim was safely removed.


The only problem removing the hood was its weight, in this case the manual was explicit enough to unhook the springs and undo the bolts all in the right order and just as I realised I was not going to be able to lift the hood up and away on my own, my lovely wife arrived home. A couple of things got caught up, but without to much difficulty the two of us got it away from the car. Finally the tourneau cover was removed and the T bar, which I intend to recover and there she was, fully naked. All that remained was a bit of a cleanup inside and out with white spirit and paper cloth.



The low loader arrived just before 9am yesterday and now Stella is in the hands of Trevor and his team. I am not sure how long it will take to find out what new metal needs to be welded in, I will just have to anxiously wait!