CRANKSHAFT BOLT

There was one aspect of my planned winter maintenance that was worrying me. To change the timing chains and sprockets I would first have to undo the big bolt that screws into the front end of the crankshaft. This bolt securely holds in place the drive belt pulley that powers the alternator and the power steering pump and also the viscous coupling to which the cooling fan is attached, the viscous coupling controls the speed that the fan revolves to no more that 2000 approx RPM irrespective of the crankshaft speed.

As you might expect this bolt is done up very tight, I think from memory 150PSI and as you might also expect takes a bit of undoing. My car is an automatic and that causes a problem as it is not possible to lock the crankshaft to stop it turning when trying to undo this bolt. The Stag Forum offers various solutions, to either lock the crankshaft or to shock the nut undone. Some of the suggestions I thought were a bit risky, so I opted for the tried and tested option, which required a very long lever and socket and a 18 inch Stillson wrench.

In the past when I needed extra leverage I slipped the handle of a long defunct bottle jack over the lever of my 1/2 inch socket set, effectively doubling it's length, but for this job I decided I needed the proper tool. My local motor accessory shop did me proud by selling me a 24 inch breaker bar from STAG TOOLS, how appropriate is that. The other tool needed is a very large wrench and although I tried all the nearby tool stores to no avail, I eventually got a decent second hand Record Stillson type wrench from an EBay seller.

The procedure was to adjust the Stillson as tightly as possible around the large circular part to the rear of the pulley block and with the handle resting on a block of wood which in turn rested on the chassis rail, the wood was to spread the load so as not to damage the chassis rail.

With the correct socket and the long leverage of the breaker bar apply the necessary pull to undo the bolt. The thing about a Stillson type wrench is that the more pressure you apply the tighter the teeth bite and without any drama, pings or sudden clicks the bolt just started to undo, brilliant.

With the help of a long pry bar, the viscous coupling and fan blades easily slipped of the crankshaft.

For only the second time I deployed my large gear puller and again the pulley block easily slipped of the shaft, exposing the key left in the crankshaft and the corresponding keyway in the pulley.

 Nothing now preventing me from removing the timing chest cover in the New Year and replacing the timing chains. In between while I have been gradually rubbing down the red Hammerite paint on the right hand side of the engine bay, slow work but getting there, that is cold work, but I do want to complete this messy job before I do anything else.

WINTER MAINTENANCE

I'm a lucky fella, I was wondering how I was going to achieve my intended list of jobs on Stella, as my garage is too stuffed with, well, stuff to be able to get around her in the garage, when an empty garage suddenly became available four down from mine.

Stella is now reversed into this empty garage and I have just enough room to work around her. So work has begun. There are three jobs to do and they are all sort of connected. The main one is to strip the engine bay of all ancillaries, but not the engine, flatten down the awful red Hammerite paint that somebody painted over the original white paint and of course respray with Rover White paint. The second job is to refurbish the front brake callipers and the master cylinder and replace all the connecting pipework and hoses. The final job is to replace the timing chains,sprockets and tensioners.

Radiator, battery, steering pump, alternator, fuel pressure regulator, servo/master cylinder, screen washer bottle and all wiring and pipework has now been removed from engine bay and stored at the back end of garage

Just the last couple of bits and bobs to remove and then I can start rubbing down the red Hammerite. I will have to wait for warmer weather before I can spray, but there is no hurry.

I have also removed the front brake callipers, so time to order up stuff in readiness, Refurb kits for the callipers and master cylinder, timing chain etc. I already have the copper brake pipes so I can start bending them to the required shape. so plenty to be getting on with, Christmas activities allowing.